| |
   
Exterior emulsion made in Savina co is used as decorative
and protective interior and exterior coating for building
surface based on cement, concrete, masonry, plaster, amiang,
wood etc.
The paint
has beautiful color, easy apply and nontoxicity because it
is soluble in water.
Technical
characteristic
The paint has high adhesion on all surfaces. Coating film
is hard dried, smooth, water and alkali and weather resistance,
prevent the fungus and algae grow. If the wall is dusty, can
clean by soap solution to become beautiful as new wall.
Method
of use
To keep good quality for the building should make sure these
items:
Quality
of the wall: smooth, dry and good structure.
Method
of paint
Protection
of building after painting.
We
introduce the method of use to the customers in order to get
the best benefit and durability of building.
Preparation
of surface
For
old wall
Old
coating of lime water must be remove by sandpaper or west
stone and smoothening the wall.
If
the wall is coveraged by fungies and algee must clean all
of them, then brush or spray antifungies solution GM 01 or
GM 02, let it dry for 24 hours, clean again by sandpaper and
brush.
If
the wall is bad structure should get out all the plaster and
replaster up. Let the wall dried before repainting ( humidity
up to 6% or after 2 weeks replaster )
Old
paint coating if the old coating is good condition only cleans
the wall by sandpaper or brush.
For
new wall
Clean
the wall by sandpaper, smoothening the wall. The surface of
wall must be dry (humidity up to 6%) at the painting.
Painting
Painting only on the dried and clean walls. During painting
if rain should stop immediately.
Apply
by roller, brush or spraying.
Smoothening
the wall :
If necessary can smoothen the wall by SAVINA plaster
power . Use the chopper press the paint on to the wall, let
dry for 24 hours, sand the wall by sandpaper before repainting.
Thinner: Can thin by 10-15 % water. Paint 2 coats min., repainting
interval in 2 hours.
Attention: Use the roller after vertical direction of the
wall, from left to right is easier using. The roller must
be always cleaned.
Antifungous
solution:
For
the old walls with fungous and algae grown, before repainting
must kill and remove all of these by antifungae solutions:
GM
-01: for old walls with general and fungus grow
GM-02:
for old walls with strong algae and fungous grow
Technical
specification
|
Item
|
Savina H1
|
|
Condition in container
|
When being stirred, it makes uniform condition without
any hard lumps
|
|
Low-temperature stability ( -50C )
|
No
deterioration
|
|
Application properties
|
when making twice coatings, no impediment for brushing
work
|
|
200C
|
2 max.
|
|
|
50C
|
4
max.
|
|
|
Appearance of paint film
|
No unusualness in appearance of paint film
|
|
Contract ratio ( white and tint *)
|
0,95 min.
|
|
Special
gloss
|
70 min
|
|
Water resistance
|
Gloss retention of 80 % or more and no unusualness
on paint film when immersed for 96 hours
|
|
Alkali
resistance
|
Gloss
retention of 65% or more and no unusualness on paint
film when immersed for 7 days
|
|
Wash
ability
|
Endurable for washings of 1000 times
|
|
Humidity and cool-heat cycling resistance
|
Gloss retention of 80% or more and endurable for humidity
and cool-heat cycling test
|
|
Accelerated weather resistance
|
After 480 hours test, gloss retention is 60 % or more,
the degree of chalking is 8 marks or higher, and the
degree of color change is not larger than that on
evaluation sample
|
|
Weather
resistance
|
After
12 months test, the degree of chalking is 6 marks
or higher, there are no cracking, peeling, and swelling,
and the degree of color change and gloss change are
not larger than those on evaluation sample
|
Tint:
Tint means light color like gray, pink, cream, light green,
light blue, or others.
Note:
Keep pails tightly closed. Any pails, which are opened,
should be carefully resealed.
Note: Avoid skin and eyes contact. Wear protection equipment
exp.: glove, gauze mask, and glasses... when paint spraying.
Isolated from sources of heat, sparks and all naked light.
|
