Interior
Emulsion SAVINA N1
  
Interior
emulsion made in Savina is used as decorative and protective
coating for building surface based on cement, concrete, masonry,
plaster, amiang, wood etc
The paint has beautiful color, easy apply and nontoxicity
because it is soluble in water.
Technical
characteristic
The paint has
high adhesion on all surfaces. Coating film is hard dried,
smooth, water and alkali and weather resistance, prevent the
fungous and algae grow. If the wall is dusty, can clean by
soap solution to become beautiful as new wall.
Method
of use
To keep good quality
for the building should make sure these items:
Quality of the wall: smooth, dry and good structure.
Method of paint
Protection of building after painting.
We introduce the method of use to the customers in order to
get the best benefit and durability of building.
Preparation
of surface
For
old wall:
Old coating of lime water must be remove by sandpaper or west
stone and smoothening the wall.
If the wall is coverage by fungous and algae must clean all
of them, then brush or spray antifungous solution GM-01 or
GM-02, let it dry for 24 hours, clean again by sandpaper and
brush.
If the wall is bad structure should get out all the plaster
and replaster up. Let the wall dried before repainting ( humidity
up to 6% or affter 2 weks replaster )
Old
paint coating :If the old coating is good condition only clean
the wall by sandpaper or brush.
For
new wall
Clean the wall by sandpaper, smoothening the wall. The
surface of wall must be dry ( humidity up to 6% ) at the painting.
Painting
Painting only on the dried and clean walls. during painting
if rain should stop immediately.apply by spressing, roller,
brush or spraying.
smoothning the wall :
if necessary can smoothen the wall by SAVINA plaster
power . use the chopper press the paint on to the wall, let
dry for 24 hours, sand the wall by sandpaper before repainting.
thinner : can thin by 10-15 % water. paint 2 coats min., repainting
interval in 2 hours.
attention: use the roller after vertical direction of the
wall, from left to right is easier using. the roller must
be always cleaned.
Antifungous
solution:
For the old walls with fungous and algae grown, before repainting
must kill and remove all of these by antifungae solutions:
GM -01: for old walls with general and fungus grow
GM-02: for old walls with strong algae and fungous grow
Technical
specification
|
Item
|
SAVINA
N1
|
|
Condition
in container
|
To
be free from hard lump and to become uniform when
stirred
|
|
Application
properties
|
No
hindrance for coating work when brush coating or roller
brush coating is appliede
|
|
Low-temperature
stability
|
No
deterioration in quality when cooled at -100C
|
|
Stability
for warming preservation
|
To
be stable when being stored for 7 days at 500C
|
|
Drying
time ( tack free )
|
within
2 h
|
|
Appearance
of paint film
|
Normal
in appearance of paint film
|
|
Film-formability
at low temperature
|
No
unusualness in film formation at 5o0C
|
|
Spreading
rate
|
Capable
of coating at least 4m2 per 1 l by two- time application
|
|
Contract
ratio ( white and tint *)
|
0,94
min.
|
|
Water
resistance
|
No
unusualness when immersed for 96 h
|
|
Alkali
resistance
|
No
unusualness when immersed for solution saturated with
calcium hydroxide for 48 h
|
|
Moisture
resistance
|
No
unusualness when moisture resistance is tested for
24h
|
|
Washability
|
Durable
for 500 times washings.
|
|
Fungus
resistance
|
Showing
fungus resistance
|
1.Paint
is not still used and remaines that must be keep tightly cosed
storage in dry and ventilated places.
2. Should perform at vetilate place. Isolate from sources
of heat.
3.Note: Avoid skin and eyes contact. Wear protection equipment
exp.: glove, gauze mask, and glasses... when paint spraying.
|
